Universal Security Instruments MP118 Manual de usuario Pagina 175
- Pagina / 194
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
PAT700 Total Organic Carbon Analyzer – Maintenance and Troubleshooting Page 167
Anatel Operator Manual
9) Press and hold the lamp retaining clip to release the UV lamp. While pressing the
lamp retaining clip, carefully withdraw the lamp from the lamp holder. DO NOT
touch the glass surfaces of the lamps.
10) Holding the lamp by its metal sleeve, insert the new lamp into the lamp holder hole
and clip into place. The lamp is self-aligning. Ensure that the lamp is locked in place
by the lamp retaining clip.
11) Reinsert the lamp module into the instrument by centering it over the manifold
assembly and gently sliding the module down to the manifold until it locks into
place.
- ANATEL PAT700 On-line Total 1
- Organic Carbon Analyzer 1
- Table of Contents 3
- Chapter 3 Startup 4
- Chapter 4 Run Modes 4
- Chapter 5 Setup 4
- Chapter 1 Before You Begin 9
- 1.3 RFID technology 10
- 1.5 Safety 11
- 1.6 Hazard information 12
- 1.7 FCC conformance 12
- 1.8 EU directives 13
- 1.9 Precautionary labels 14
- 1.10 Symbols and marks 15
- 1.11 Patents 15
- 1.12 Definitions of terms 15
- 1.13 Customer service 16
- Chapter 2 Installation 17
- 2.2 Orientation and mounting 18
- Mounting to a wall 20
- 2.3 Plumbing connections 23
- Isolation valve 23
- Water inlet and outlet 24
- 2.4 Setting sample flow rate 26
- Power supply wiring 28
- I/O wiring 29
- Discrete inputs 30
- Discrete outputs 32
- 2.7 Serial ports 38
- 2.8 RS-232 commands 39
- Conventions 39
- Mode setup commands 40
- Data read commands 40
- Data logger commands 41
- Parameter setup command 43
- Diagnostic commands 46
- 3.3 Logging on and off 48
- Auto logoff 48
- 3.4 Home screen 49
- Sliding toolbar 49
- 3.5 Home screen data views 51
- Current tab 51
- Log view tab 53
- Graph tab 53
- 4.2 Accessing run modes 56
- 4.3 Online TOC mode 56
- Sampling with pressure 57
- 4.4 Conductivity mode 57
- 4.5 Standby mode 58
- 4.6 Offline mode 58
- 4.7 Manual TOC Sample 59
- 4.8 Self clean mode 59
- General tab 62
- Idle tab 63
- Digital control tab 64
- Stabilization tab 65
- P5 Curve 66
- 5.4 System 67
- Display tab 68
- Sounds tab 69
- Network tab 69
- Backlight tab 70
- 5.5 Alarms 71
- 5.6 Analogs 73
- 5.7 Printer 74
- Conductivity tab 77
- 5.8 Security 77
- Settings tab 79
- Users tab 80
- Audit trail tab 82
- 5.9 Bottles 84
- TOC calibration tab 84
- Conductivity calibration tab 85
- TOC validation tab 86
- System suitability tab 86
- Grab sample tab 87
- 5.10 Password 88
- 5.11 Factory 89
- Cell tab 90
- Thermistor tab 90
- User slopes tab 91
- Algorithm tab 91
- OxFiles tab 92
- Chapter 6 Bottle Mode 93
- System suitability protocol 94
- 6.2 Accessing bottle mode 94
- 6.3 Bottle mode dialog box 94
- 6.4 Run standards 95
- 6.5 TOC calibration 96
- TOC calibration setup 96
- TOC calibration procedure 97
- Operator Manual Anatel 100
- Anatel Operator Manual 101
- 6.6 Conductivity calibration 104
- Verification resistor 106
- 6.7 TOC validation 108
- 6.8 System suitability test 110
- 6.9 Grab sample 112
- 6.10 Excursion mode 116
- Excursion with validation 117
- Excursion without validation 119
- 6.11 Bottle flush mode 121
- Chapter 7 Alarms 123
- 7.2 Alarm acknowledgement 124
- 7.3 Alarm details 125
- 7.4 Alarm codes 125
- Error alarms 126
- Critical error alarms 127
- Warning alarms 127
- TOC alarms 130
- Measurement alarms 130
- Audible alarms 130
- Chapter 8 Diagnostics 131
- PAT700 lamp replacement 133
- 8.4 Tests tab 133
- RS-232 test 134
- Digital I/O test 135
- 4-20 mA output test 135
- Printer test 136
- Plumbing test 136
- Pump test 140
- Fan test 141
- RFID test 142
- 8.5 Test tab 143
- 8.6 Calibration dates tab 143
- Chapter 9 Data Review 145
- 9.3 Export data 146
- 9.4 Filter data 147
- Chapter 10 Signing On and Off 149
- 10.2 Password 150
- 10.3 Expired password 150
- 10.4 Backdoor password 150
- Chapter 11 Modbus Protocol 151
- 11.2 Modbus/TCP Driver 152
- Modbus Protocol 152
- TCP/IP Interface 153
- Data Model 154
- Data Encoding 155
- IP Address 156
- Data Dictionary 158
- Configuration Block 160
- (Format: Double Float) 164
- User Security Block 168
- 12.1 Maintenance 171
- UV Detect technology 171
- Lamp replacement procedure 172
- Self clean mode 176
- 12.2 Water filter replacement 177
- 12.3 Troubleshooting 178
- Fuse replacement 178
- Technical support 178
- Return procedures 179
- Draining the analyzer 180
- Appendix A: Specifications 183
- Physical specifications 184
- Appendix B: CE Conformance 187
Relacionado con productos y manuales para Detectores de humo Universal Security Instruments MP118
(10 paginas)
(18 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales